Поиск по STEAMB

Игры и программы по онлайну, скины по объёму продаж

Ничего не найдено

Попробуйте другое название или переключите категорию.

Меню

Чертежи

(HGI) S-Ship Printer v.3 a.k.a. SSP-3

Положительные голоса97%39 голосов игроков
Подписчики1,5 тыс.1 506 в Steam Workshop
Размер файла842,63 КБЗагрузка через Steam
Обновление автора28 мая 2015 г.Дата обновления материала

Фото и видео: 1 из 8. Материалы автора из Steam Workshop.

Фото и видео: 1 из 8
Установить через Steam

О материале

«(HGI) S-Ship Printer v.3 a.k.a. SSP-3» — материал мастерской Space Engineers. Моды, чертежи кораблей, скрипты и миры для Space Engineers. Данные Steam, описание автора и ссылка для установки через подписку. Совместимость редакцией не проверена.

Описание автора

I took a basic ship printer design that Ravric use on his Midnight Carrier and took it to the next level. And while not 100% perfect its does a good job of printing MOST (some are to big and some cause the piston to go bat shit crazy) small ships.

This printer has the ability to store 10 different ship is its projectors (if you think 10 is too many the first one 1 was going to build would have had 24). Once a ship is place in a projector and is aligned properly with the construction boom you can save the ship in the projector for later. So if say it gets destroyed or you want another its at the push of a few buttons.

There Printer does has its limitations, most can be easily over come with a little engineering. If you want it bigger or smaller you just need to add/remove welders assign them to the proper groups and adjust the sensor field. Plus if you have bigger ship you can have the piston go up another 3 meters.

This printer use the Larger rotor top, small rotor base in two places. This can be built in survival but it can be a bit tricky for those who have never done it before.

I used a script "Precise Timers" by SioxerNic which allows the timers to work off of frames per second in stead of seconds, which allow for better timer control. This helped me turn the welders on/off quicker which helps reduce lag.

I will also include the timer and group setups along with the sensor settings so if you want to build you own printer its a bit easier.

No Mods were used in the creation of this printer.

"Precise Timers" - https://steamcommunity.com/sharedfiles/filedetails/?id=424955427&searchtext=precise+timers

"Midnight Carrier" - https://steamcommunity.com/sharedfiles/filedetails/?id=428877518

An earlier version of this printer was show in a video by Scottsdragon here is the link to that video as well. https://www.youtube.com/watch?v=Y68GZcJrFvo

Видео автораОткрыть в YouTube ↗
Оригинал в Steam Workshop

Как установить и запустить

Откройте оригинальную страницу в Steam Workshop, проверьте версию игры, зависимости и порядок загрузки в описании автора. Нажмите «Подписаться» и дождитесь загрузки Steam. Включите материал в меню модификаций или контента игры, если это требуется. Совместимость и запуск редакцией не проверены.

Настройки cookies

Вы можете изменить выбор в любой момент. Отказ от аналитики не ограничивает доступ к сайту.

Технологии, провайдеры и сроки хранения