Поиск по STEAMB

Игры и программы по онлайну, скины по объёму продаж

Ничего не найдено

Попробуйте другое название или переключите категорию.

Меню

Чертежи

Amphion - Hydra - Autominer

Положительные голоса98%303 голосов игроков
Подписчики2 тыс.2 024 в Steam Workshop
Размер файла488,5 КБЗагрузка через Steam
Обновление автора13 июн. 2015 г.Дата обновления материала

Изображение 1 из 5. Материалы автора из Steam Workshop.

Изображение 1 из 5
Установить через Steam

О материале

«Amphion - Hydra - Autominer» — материал мастерской Space Engineers. Моды, чертежи кораблей, скрипты и миры для Space Engineers. Данные Steam, описание автора и ссылка для установки через подписку. Совместимость редакцией не проверена.

Описание автора

The Amphion Corporation is proud to present a new step forward in automated mining and tunneling! The Hydra. The Hydra utilizes GPS waypoints to drill through asteroids, though it is completely capable of doing a one-shot drilling task as well, though this will result in some deviation from the intended path. Using waypoints will result in clean, direct tunnels. The whole purpose of setting up the Hydra is to provide a sizable entry point. It's not a cheap craft, either. Fifteen drills, numerous containers, a large reactor, and several other items make building it a bit on the expensive side, but ore collection will never be smoother!

With a set of four batteries, the Hydra can easily be operated from a nearby base solely on rechargeable power. The coupling timer blocks are set up for recharging while docked. The wheels are there to prevent the ship from damaging itself.

BUTTON MASHING METHOD

Although the ship is designed for autopilot, it can still be used like a traditional auto-miner, albeit with a bit of path deflection as an unfortunate possibility. The button on the top right initiates the drilling sequence. Tap it a couple times to make it go faster. Once it's finished its job, it'll stop drilling. The number of times you hit the start is the same number of times you have to hit the stop to get it to stop.

FOR SIMPLE JOBS INVOLVING MANUAL RETRIEVAL

-Set up a waypoint about 20m away from where you want the entry point to be. Turn on precision mode for this waypoint's actions. Trigger the timer block (using waypoint configuration) labeled "Timer Block - Start Drilling".

-Set up a waypoint near the entry point.

-Set up a waypoint on the other side of the asteroid you wish to drill through. Turn off precision mode in the remote control and trigger the timer block labeled "Timer Block - Stop Drilling" through the waypoint configuration menu.

-Afterward, just pick up the ore from its connector!

FOR COMPLEX JOBS INVOLVING AUTOMATED CARGO DROPOFF

Setting up the GPS waypoints (for docking and automated ore deposits) is best done with the Loggerhead, as it can be manually operated via cockpit and the waypoints adjusted according to the positioning of the remote control block located beneath its connector. Although it can be done through remote control with the Hydra, it's just a lot less reliable and takes longer. Please refer to the guide attached with the Loggerhead if you wish to use it. Otherwise, if you are already familiar with autopilot configuration, please proceed.

Step 1. -Make sure the connector and remote control line up with the custom GPS waypoint at your station. -Make sure that the waypoints are set up like the Loggerhead's waypoints. -The waypoint directly next to the connector should have Timer Block - Coupling as an action, set to trigger immediately -The waypoint above and about 20m away from the connector should have the remote control set to back and Timer Block - Precision Mode set to trigger immediately -All other waypoints should avoid collision as best as possible en route to the asteroid you wish to mine. -Please ensure that the remote control is also set to One Way instead of Patrol or Circle

Step 2. -Set up a waypoint approximately 50m away from your entry point.

Step 3. -Set up a waypoint within 10m of your entry point. -At this waypoint (entry point), enable precision mode to trigger right away through the timer block. The sensor should take care of the rest.

Step 4. -Set up a waypoint on the other side of the asteroid (or, if it's hollow, inside the asteroid).

Step 5. -Verify that the waypoints can connect in a relatively straight line.

Step 6. -Set up a waypoint near the exit point. The Timer Block - Flight Mode should be set to trigger 10 seconds after reaching this waypoint. This will allow time for the vessel to expel some of the excess stone that was accumulated during its drilling run.

Step 7. -Have the vessel return to base to dump its cargo at the connector set up in the first step. If you wish to repeat the process, delete the old waypoints and set up new waypoints, following the previous 7 steps.

Enjoy!

WARNING!

In case of emergencies while drilling, there are two ways that the Hydra can be stopped. One, via a sensor facing forward, the other, via two buttons located on the top of the craft. It is best to turn off the drills before attempting to disengage autopilot.

And as always: RTFM.

Primary features -Automatic drilling via waypoint configuration -Easy waypoint setup for autopilot -Excellent cargo space -Expels stone automatically after drilling for easy cleanup -Two killswitches prevent the ship from inadvertently turning an unwary engineer into a strawberry milkshake, violently. One is on the tail end of the craft, the other is a sensor-based switch. -Guide wheels prevent the ship from damaging itself while drilling

Оригинал в Steam Workshop

Как установить и запустить

Откройте оригинальную страницу в Steam Workshop, проверьте версию игры, зависимости и порядок загрузки в описании автора. Нажмите «Подписаться» и дождитесь загрузки Steam. Включите материал в меню модификаций или контента игры, если это требуется. Совместимость и запуск редакцией не проверены.

Настройки cookies

Вы можете изменить выбор в любой момент. Отказ от аналитики не ограничивает доступ к сайту.

Технологии, провайдеры и сроки хранения